Computer Maintenance & Repair - Samsung Desktop PC DM300S3B-B13R WD-green 240G SSD Additional Format Windows 10 Installation Review

Good morning. This is the formative "male fox".

"KHComputer Maintenance - Kindly Honesty Computer Repair" is an abbreviation for friendly and honest computer repair business trip AS article meeting cafe.

Because of the Plague Pendemic, I received a request from a corporate customer representative who had delayed the PC check.

At that time, because of the discontinued issue of Windows 7, you thought to switch to Windows 7 and switch to Windows 10.

At that time, as the pendemic burst, it was put on hold for about 3 months to cut off face-to-face with outsiders,

You were asked on the day before Labor Day.

Your company uses three DM300S3B-B13R Samsung desktop PCs,

Here, you were using Windows 7 on a regular hard disk HDD.

The specifications are roughly the fourth-generation Pentium processor, so I think it's a good thing,

To drive Windows 10 on the HDD, it is very slow and there is a possibility that the driving experience may deteriorate.

After installing the additional SSD, you should set Windows 10.

That's why I asked a format master engineer for a computer repair business trip to Daehwa-dong, Ilsanseo-gu, Goyang.

After checking your Samsung desktop PC DM300S3B-B13R, back up the data,

We will add a SSD and tell the story of the service review after installing Windows 10.

It can be considered as a PC used in a typical corporate office.

There are quite a few document writing files on the desktop, and as you can see, it is the Windows 7 desktop.

It was difficult to deny the feeling of being slow and stuffy even to check. 

The specifications are not so bad. Intel 4th generation Haswell Pentium G3240 (2 core 2 thread).

Memory is DDR4 8G, which may not be as good as the new ones, but it's not bad for corporate and office documents and business. However, it is better to run Windows 10 on a regular HDD. 

It was difficult to say that the state was very pleasant, but in that state, it was worth saving a backup.

If you don't have any doubt, you can try to boot and save the USBPE, but since Sergei Strelec PE doesn't speak Korean, it is not bad to back up in this state, if possible, because the contents of the file saved in Korean are not known. 

This is a side view of the Samsung Desktop PC DM300S3B-B13R.

It is an LP type slim, and a lot of dust has accumulated on the side lid grill.

The LP type slim thinks that heat management and cooling are not good,

Nevertheless, it seems that LP type slim bodies are not popular among brand PCs. 

This is the SSD 240G WD-green product you want to add.

In the 240G band, WD-green is an inexpensive and cheap Sungbye position,

I think it is reasonable to prefer WD-Blue over 500G. 

Due to the structural limitations of the LP slim case, the SSD is attached to both sides with a double-sided adhesive and attached to a relatively spacious area with a front USB.

Unlike hard disks, it is not sensitive to vibration, so it can be fixed with only adhesive.

If possible, it would be better to fix it with screws, but if you are a computer repairer, as you know, I do not know that brand PCs are a bit funny to fix SSDs separately.

If HDD is installed, it shouldn't be that way, but for SSD, it is not a moral flaw even if it is handled properly.

First of all, the thoroughness of the installation is reduced from the unavoidable line to the appropriate line.

It would be best to install the software honestly and set the software with sincerity. :) 

 This is the BIOS firmware setting screen.

Check that the 240G SSD and 500Gb general hard disk are recognized together.

Before 4th generation, AHCI could be disabled.

If the settings in this part are misaligned, of course the blue screen was blank.

In case of general hard disk, it is better to activate AHCI and set the operating system.

In the case of SSD, there is no big limitation. However, it may be better to automatically or to the initial value.

Because, if it is a product before the 4th generation, it will gradually become a retirement that needs to be decommissioned to enter the category of Chosun Com.

This is because the initialization may occur gradually due to the BIOS battery problem.

In this case, if the operating system is set according to the initial settings at the time of initialization, even if the initial checksum is pressed, just press F1 and synchronize and adjust the time after booting.

However, if the AHCI value is different from the initial setting, the blue screen may appear when it is initialized. 

The Samsung PC boot device selection key is F10.

It is strange that the 2nd generation products had to press ESC ㅡ ㅡ

Temporary boot with Sergei Strelec Win10PE UEFI prepared by USB. 

It is confirmed that the normal hard disk used in the storage device is okay, and that the SSDs of the three products are even more defective.

These indicators can be meaningfully checked through Hd-tune or Crystal-Disk-Info. 

Run DiskpartGUImicro to grab a 240G SSD and GPT / UEFI partition format.

Then, proceed with the format Windows 10 installation using WinNTsetup. 

The existing hard disk is partitioned and merged.

Anyway, the partition0 area of ​​the hard disk, that is, the C drive, is already unnecessary because it has been backed up, so there is no reason to leave the previous contents.

This is because, if it has been set and initialized for a long time, which was mentioned earlier, in the end, it may try to boot Windows 7, which was previously left on the hard disk.

For this reason, the reason why I'm trying to mount the SSD as the front part of Sata0 at all is that even if the PC is sensible, it will try to boot the operating system installed later in the SSD first.

This is important, but the hard disk is also in good condition, so it is more convenient for customers and users to merge and use it as a more obvious D drive. .

Of course, there are some exceptions that do not necessarily follow these rules.

In some cases, if it is related to a special program, if it is bitten by an industrial machine, or if it does not apply to the newly installed drive, it may be better to return it to the old state. In this case, if the existing contents are lost, it may become untouchable.

However, because such cases are extremely rare, it is only a story that merging is as universal as possible. 

Windows 10 installation or initial setup time seems to be working as expected, like an SSD.

The UEFI / Quick Boot Configuration status has been effectively observed. 

Edge also appears (although I deleted it anyway), and I check that the major web browsers appear.

In other words, it is about confirming that the Internet is good.

Users of office and corporate customers probably don't like the edge of the app.

Because once you need ActiveX thoroughly, you need Explorer, and if you get stuck in a quick saying that you are close to pdf viewers, you will shout at me that Pdf won't open. It may not be used well, but surprisingly, the edge has experienced a lot of errors in the native app as a pdf viewer.

The reason is that even if you put a basic app with another decent utility as a PDF viewer, it may become a basic app that the edge does not do at any moment, and it may make users uncomfortable.

For that reason, I just remove the edge. 

After confirming that the device drivers are completely installed, the update is natural, but they are all finished with the latest status.

A separate graphic device (VGA card) is only used to display the screen with a CPU processor built-in graphic that does not exist.

It is a com that should be used only for work in the office.

Since it is equipped with an SSD and finished setting, the main page of our homecoming cafe is also lightly opened.

This is what appears when you click the "Online Support" link text.

In addition, the connection status of file sharing with PCs by colleagues in the vicinity,

Also, I used two network copiers, and I had a label printer in it, and I checked the connection.

From the network copier, the driver was checked for printing, and the remote SMB scan was confirmed.

In the case of label printers, we only need to connect the driver, check the customer's detailed settings (label print size and composition setting), and the service mission for all customers is completed.

I mentioned that the fourth generation Pentium is not really good at the outset,

Just in the office, I just want to watch YouTube when I don't have documents or computer on Windows 10. Sometimes, it's certainly a good use.

Therefore, it is still considered reasonable to set up an additional SSD in the state of being a normal hard disk.

Of course, if there is an SSD, in normal case, it will be solved by re-installation.

If there is one downside, if it is about 4 generations, it has already passed the end of life,

If the core parts are small, it will be a bit troublesome.

We will always consider customer's satisfaction first, and we will be reborn as a computer repair AS master with the most reasonable and cost-effective setting and sincerity setting effort.

Thank you.